November 24, 2024
Show Correct answer after 3 Failures - Workflow

Table of Contents

Intro

Just lately I posted an instance undertaking, resolution to a discussion board query. On MCQ slides, one proper resolution, with 3 makes an attempt the right kind resolution must be indicated if the learner fails three times. The proposed answers had been the use of other failure messages (can be utilized each for responsive and non-responsive initiatives) or highlighting the right kind resolution (simplest in non-responsive undertaking). Each workflows are simplest imaginable in Captivate Vintage. The brand new model is lacking the function to have more than one failure messages connected to makes an attempt. Because the new model is simplest responsive, the spotlight could also be excluded.

Hyperlink to the weblog with the instance undertaking:

Display proper resolution after 3 disasters on MCQ – eLearning (adobe.com)

On this weblog you get a step by step clarification of each workflows.

Workflow: use 3 Failure messages

  1. Arrange the Quiz Houses like this; this setup doesn’t come with the semblance of a spotlight (see under in the second one section). If that’s the case the Final Try wishes a complicated or a shared motion as a substitute of ‘Proceed’. As same old I dragged the pausing level on each and every quiz slide from the default 1.5 secs nearer to the tip of the slide?
  2. Because of the selection for three failure messages (which is the utmost), two additional failure messages can have been added at the slide. It isn’t a set location, is determined by the theme. The 2 additional messages (2 and three) will ceaselessly be stacked.  This implies you want to transport the highest one (3) to look message 2. To locate the message quantity, hover over the message. On this screenshot I hovered over the second one message, after dragging the 3rd one down as it used to be overlaying the second one:

  3. Edit the messages and rearrange them, you’ll stack them once more (as I did on the second one query) or replicate the arrange of the primary quiz slide:

Workflow: highlighting

  1. Create the spotlight form over the right kind resolution. Keep in mind: all customized shapes are stacked under the embedded quiz gadgets. To make it visual you must ensure that the ‘resolution house’ is a minimum of partly clear:

    On this case the solution house had a fill colour, however at 60% alpha. The yellow form in the back of it is going to mix, you’ll need to search for a right kind colour aggregate.

  2. A result of the stacking of the spotlight form below the solution house: it’s tricky to choose that spotlight house at the degree. Make sure you open the Timeline the place variety is more straightforward. You want to choose the spotlight an set it to invisible in output in its Houses panel:
  3. You want to create a complicated or shared motion, to be precipitated through the Final Try match of the query slide (Quiz Houses). That is the complicated motion,  the marked pieces would be the parameters within the shared motion. I in reality counsel to take that additional step, as a result of you’re going to reuse this motion more than one occasions. In fact you’ll make a choice any other Front impact (I used FadedZoomIn)
  4. For the shared motion I indicated the parameters within the screenshot of the complicated motion, and this is the parameter description. The spotlight field won’t all the time be in the similar location, therefore that parameter. It isn’t imaginable to have the spotlight seem similtaneously the 3rd failure message. That message seems with step one of the Post procedure, while the motion to turn the spotlight is precipitated through the Final Try motion, which is with the second one step of that procedure.

You’ll have extra questions, however I be expecting those to pop up.

  1. Can this even be finished in a Fluid Bins (responsive undertaking in Captivate Vintage)?
    1. Sure, you’ll even have as much as 3 Failure messages. The 2 additional messages it will be inserted out of doors of the static fluid field which has all of the different messages. I like to recommend to arrange after enhancing, and feature all of them stacked in that fluid field.
    2. The spotlight isn’t imaginable as a result of you can’t stack a form in the similar location as a person resolution, and the ones solutions are embedded gadgets because of this that they’ve no ID and can not have states which may well be used to switch the colour of the right kind resolution.
  2. Can this workflow be finished in New Captivate (12.2)?
    No longer at this second for a number of causes:
    1. There’s no risk to select greater than 1 failure message. That message is a state in a multistate object, to which you’ll no longer upload customized states. However even though that risk existed, you can’t deal with the multistate object because it has no ID.
    2. You can’t upload a spotlight form to the right kind resolution. You can’t upload states to the person solutions, and even though that used to be imaginable, identical drawback arises: that multistate object wouldn’t have an ID, so you can’t trade its state.

Leave a Reply

Your email address will not be published. Required fields are marked *